Skip to main content

Layers and cut settings

Colour is the layer​

Every object belongs to a layer, and every layer has a colour from the palette at the bottom (00–29, plus the tool layers T1 and T2). Click a colour in the palette to put the selection on that layer.

The layer holds all laser settings. Objects, including images, never carry their own speed or power: to laser something differently, put it on another layer. That way a layer is one operation of the job, and the same settings apply to everything on it.

The Cuts / Layers window lists the layers that are in use, with mode, speed, power, air assist and output. Values can be edited right in the table; drag rows to change the order in which the layers are lasered.

Modes​

ModeWhat happens
LineThe laser follows the outlines: cutting and scoring.
FillClosed shapes are engraved line by line (or in rings with offset fill). Open lines are skipped.

Images can sit on any layer. The table then shows “+ Image”, and the layer dialog gets an Image section with line interval and image settings. Each image keeps its own image mode (see Images and tracing); speed and power come from the layer.

Tool layers T1 and T2​

T1 and T2 are never lasered. Use them for construction lines, the outline of a workpiece, camera images to trace, or the path of a text on a path you do not want to cut.

Output and visibility​

  • Output decides whether a layer is lasered at all. Hidden layers and objects are still lasered if their output is on; KizamuBeam warns you about that before the job.
  • In the Objects window single objects can be set to Don’t laser: they stay visible (faded) but are not lasered, not written to G-code and not checked.

Cut settings​

Double-click a layer (in the table or in the palette) to open its Cut Settings. The tabs at the top switch between the layer and its sub-layers. The settings are grouped into foldable sections: General (name, mode, speed, power, passes and output), Geometry (kerf offset and focus position), Line or Fill, Images, Image cut (optional) and Appearance in 3D. Which fields appear depends on the mode.

Layer type​

Type says what the layer does to the workpiece: Cut, Engrave or Mark. Automatic (the default) decides from the mode and the sub-layers, as before. Engrave and Mark layers never cut through, not even with closed shapes: the 3D view engraves them onto the part below, the design check does not treat them as cuts, and nesting moves them together with the part they lie on. The G-code does not change. The type is saved in the project and in material library entries.

Common to all modes​

SettingMeaning
Speed (mm/min)Feed rate while the laser is on.
Max Power (%) / Min Power (%)The layer’s power. Min Power is used where power is lowered: in power ramps and for the lightest tones of grayscale images.
PassesHow often the layer is repeated.
Air AssistSwitches air assist (M8 or M7) on for this layer.
Z offset (mm) and Deeper per pass (mm)Only with a motorized Z axis: move the focus relative to the start height, and go deeper with each pass.
MaterialLinks the layer to an entry of the material library; also used by the 3D view and the fit calibration.

Line​

SettingMeaning
Kerf Offset (mm)Moves the cut outward on outer contours and inward on holes, so parts keep their nominal size. Usually half the kerf width.
TabsLeaves small bridges uncut so parts do not fall out: count per shape or spacing, tab size, optionally skip inner shapes. Max tabs per shape and Min tabs per shape limit the number (0 = unlimited). Tab power (%) above 0 cuts the tabs with reduced power instead of leaving the laser off. Remove tabs deletes the automatic tabs of this layer.
PerforationCuts a given length, then leaves a gap, for tear-off edges or fold lines.
Lead-in / Lead-outA straight line at an angle or an arc into and out of the contour, always on the waste side, so the start point leaves no mark on the part.
Overcut (mm)Continues past the start point to make sure the contour is closed.
Power rampLowers the power toward corners (from a set change of direction) to avoid burn marks, optionally at the start and end of each cut too.
DwellStart pause and End pause (ms) before and after each cut let the head settle. With Pierce (Cut-Through) the beam fires during the start pause at the Pierce power, so thick material is pierced reliably. Smoothieware only pauses without the beam; Ruida controllers do not pause.
Duplicate linesRemoves lines that lie on top of each other before cutting, so nothing is cut twice.

Fill​

SettingMeaning
Line interval (mm) or Lines per inchDistance between the fill lines.
Scan angle (°)Direction of the lines: 0° horizontal, 90° vertical.
CrosshatchA second pass rotated by 90°.
Bi-directionalLasers in both directions (faster).
Overscan (%)Runs past the edges with the laser off, so the head is at full speed when it fires. Avoids darker edges.
Fill styleLine by line, or Offset fill: rings that follow the outline inward.

Defaults resets the fields to the defaults of the selected mode.

Images and image cut​

When the layer holds images, the Images section shows the raster settings of the layer and a button to Adjust Image …. Under Image cut (optional) the layer can also cut around its images after engraving them, with its own line settings: first all images of the layer are engraved, then all their contours are cut. Each image is cut along its visible boundary, or along a closed shape you assign with Assign image cut contour in the context menu (select the image and the shape). See Images and tracing.

Sub-layers​

+ Sub-layer adds further operations on the same shapes, each with its own mode, speed, power, passes and settings. A classic use is “fill, then cut the outline” on a single layer. Sub-layers run after the layer itself and can be switched off one by one.

Appearance in 3D​

Appearance in 3D sets how the layer’s parts look in the 3D view: 21 materials from plywood to slate, acrylic and anodized aluminium, each with an optional own colour.

Material library​

The Material window stores proven settings per material and thickness and applies them to a layer with one click. See Materials and tests.

Layer defaults​

The gear at the right of the button row in Cuts / Layers (also under Edit → Settings … → Workspace and snapping) opens Layer defaults: which settings each layer 00–29 starts with.

  • Categories: Cut, Engrave and Mark are built in (they can be reset but not deleted); add your own with New or Duplicate. Each category has a type, a mode (line, fill, or fill + line as a sub-layer), speed, power, passes and the other common settings. From active layer and From library copy all settings at once, including tabs, perforation and fill style.
  • Layers: pick a category for each layer 00–29. With Apply to new projects switched on, every new project (New, a new tab, closing the last tab, first launch) starts with these layers. Opened files never change.
  • Apply to this project sets the layers of the open project to their categories as one undo step and names the used layers that changed. A layer whose values change gets its standard name back (C03) and loses the link to its library entry. Layers that hold images are left as they are.

The defaults are stored with your settings, not in the project, and travel with Transfer Settings.